- Percent grade2.6%
- Angle1.489°
- Ratio (rise : run)1 : 38.46
- Ratio (H : V)38.46 : 1
- Roof pitch0.312 in 12
- Rise over a run of 2506.5
- Slope length along the surface250.1
Enter rise and run, a percent grade, an angle, a 1:x ratio or a roof pitch, and get all the others at once, plus the rise and slope length over any horizontal distance.
Slope is rise divided by horizontal run. Percent grade is that number times 100, and the angle is its inverse tangent:
Rise and run must be in the same units, and run is the horizontal distance, not the distance measured along the slope. Uphill is positive and downhill is negative in the direction of travel.
The same slope can also be written as a ratio or a pitch:
Ramps and pipes are usually written rise to run (1:12 means 1 up for 12 across). Earthwork side slopes are written horizontal to vertical, so a 3:1 embankment is 3 across for 1 up, a grade of 33.3 percent. Roof pitch is the rise in inches per 12 inches of run, so a 6/12 roof rises 6 in per foot.
| Grade | Angle | Rise : run | Pitch (x in 12) | Typical use |
|---|---|---|---|---|
| 1% | 0.57° | 1 : 100 | 0.12 | Very gentle; looks flat |
| 2% | 1.15° | 1 : 50 | 0.24 | Typical paved road cross slope |
| 5% | 2.86° | 1 : 20 | 0.6 | Moderate highway grade |
| 8.33% | 4.76° | 1 : 12 | 1 | Maximum ADA ramp slope |
| 10% | 5.71° | 1 : 10 | 1.2 | Steep road or driveway |
| 25% | 14.04° | 1 : 4 | 3 | Low-slope roof (3/12) |
| 33.3% | 18.43° | 1 : 3 | 4 | 3H:1V embankment, 4/12 roof |
| 50% | 26.57° | 1 : 2 | 6 | 2H:1V cut slope, 6/12 roof |
| 100% | 45° | 1 : 1 | 12 | 12/12 roof, 1H:1V slope |
Grade and angle are not proportional. 10 degrees is 17.6 percent, but 45 degrees is 100 percent, and the grade heads to infinity as the angle approaches 90 degrees.
A survey gives a road centerline elevation of 312.40 ft at station 10+00 and 318.90 ft at station 12+50. Find the grade.
The angle is arctan(0.026) = 1.49°, the ratio is 1 : 38.5, and the distance along the pavement is 250 × √(1 + 0.026²) = 250.08 ft, so on gentle grades horizontal and surface lengths are nearly the same. Driving the other way, the same road is a −2.60 percent grade. These are the defaults loaded in the calculator above.
A porch is 30 in above the sidewalk. The 2010 ADA Standards for Accessible Design (405.2) allow a running slope no steeper than 1:12, and 405.6 limits one ramp run to a 30 in rise, so a single run works:
The ramp surface is 360 × √(1 + (1/12)²) = 361.2 in long at 4.76°. Landings at the top and bottom are extra. In the calculator, pick Ratio 1:x, enter 12, and enter a run of 360 to check the 30 in rise.
A gable roof spans 28 ft with a 6/12 pitch, so each side has a horizontal run of 14 ft. The slope is 6/12 = 0.5:
15.65 ft is the rafter length from the wall line to the ridge line along the slope, before the overhang and the ridge board thickness are accounted for.
The NCEES FE Reference Handbook has no separate slope formula. Grades appear in the Civil Engineering chapter, Transportation section, where vertical curves use the entering and exiting grades g1 and g2 in percent, and in leveling and earthwork problems in Surveying. Two common slips: dividing by the slope distance instead of the horizontal distance, and dropping the minus sign on a downgrade. Practice the elevation side in the leveling and percent grades lesson and the surveying practice problems.
Divide the rise (change in elevation) by the horizontal run and multiply by 100. A road that climbs 6.5 ft over 250 ft of horizontal distance has a grade of 6.5 / 250 × 100 = 2.6 percent.
No. A 100 percent grade means the rise equals the run, which is a 45 degree slope. A vertical face has no horizontal run, so its percent grade is undefined (infinite).
Take the inverse tangent of the grade as a decimal: angle = arctan(grade / 100). A 5 percent grade is arctan(0.05) = 2.86 degrees. Going back, grade = tan(angle) × 100, so 10 degrees is 17.6 percent.
In earthwork, side slopes are written horizontal to vertical (H:V), so 2:1 means 2 ft out for every 1 ft up: a 50 percent grade, or 26.6 degrees. Ramp slopes such as 1:12 are written the other way, rise to run. Check which convention the drawing uses.
Under the 2010 ADA Standards (section 405.2), a ramp running slope may not be steeper than 1:12, which is 8.33 percent or 4.76 degrees, and section 405.6 limits each ramp run to a 30 inch rise.