Steel Beam Size Calculator

Enter the span and the dead and live loads. The calculator finds the required section modulus and the lightest W-shape that passes bending, shear and deflection.

Simply supported beam, uniform load

Steel
Live-load deflection

Required Zx before beam weight = 49.2 in³

Lightest W-shape: W16x31

  • Bending Mu ≤ φMn: 187 ≤ 203 kip-ft92% used
  • Shear: 31.2 ≤ 131 kips24% used
  • Live-load deflection ≤ L/360: 0.686 ≤ 0.8 in86% used

Also works, next lightest: W14x34 (Ix 340), W18x35 (Ix 510), W14x38 (Ix 385), W16x40 (Ix 518), W18x40 (Ix 612)

Assumes the compression flange is braced along its length (by deck or joists), so lateral-torsional buckling does not govern. Shapes and properties from the AISC Shapes Database v16.0. Preliminary sizing only; have a licensed engineer design the beam, its connections and bearing.

How the Calculator Picks a Beam Size

It treats the beam as simply supported with a uniform load, which covers most floor and roof beams that sit on two supports. For each W-shape in its table (W8x10 through W30x108) it adds the beam's own weight to the dead load, then checks bending, shear and live-load deflection. The lightest shape that passes all three is the answer. Beams with point loads or overhangs: get Mmax and Vmax from the beam calculator and use the same checks below.

Required Section Modulus

For a compact W-shape whose compression flange is braced, the nominal strength is the plastic moment Mn = FyZx (AISC 360 Section F2). A few light shapes, such as W8x10 and W8x31, have noncompact flanges at Fy = 50 ksi, so the calculator reduces their Mn per Section F3. The NCEES FE Reference Handbook has the same equations and the AISC Table 3-2 "W Shapes, Selection by Zx" in the Design of Steel Components section of the Civil Engineering chapter.

If you were taught the older allowable stress method, the required elastic modulus is Sx = M/Fb with Fb = 0.66Fy = 33 ksi for A992 steel. It usually points to the same shape.

Shear and Deflection Checks

Most rolled W-shapes meet the web limit h/tw ≤ 2.24√(E/Fy), so φv = 1.0 (Section G2.1). Shear rarely controls a uniformly loaded beam unless the span is short and the load heavy. Deflection often does control long spans, which is why the lightest shape that passes bending is not always the answer. Deflection uses service live load only and E = 29,000 ksi. To see the full deflected shape, use the beam deflection calculator.

Worked Example: 24 ft Floor Beam

A simply supported A992 beam (Fy = 50 ksi) spans 24 ft and carries 0.8 kip/ft dead load and 1.0 kip/ft live load. The slab braces the top flange. Live-load deflection limit L/360. These are the calculator's default inputs.

  1. Factored load: wu = 1.2(0.8) + 1.6(1.0) = 2.56 kip/ft, so Mu = 2.56 × 24² / 8 = 184.3 kip-ft.
  2. Required Zx = 184.3 × 12 / (0.9 × 50) = 49.2 in³. W14x30 (Zx = 47.3) is too small. The lightest shape above 49.2 is W16x31 (Zx = 54.0 in³).
  3. Add self-weight: wu = 1.2(0.8 + 0.031) + 1.6(1.0) = 2.597 kip/ft, Mu = 187.0 kip-ft. φMn = 0.9 × 50 × 54.0 / 12 = 202.5 kip-ft. OK (92% used).
  4. Shear: Vu = 2.597 × 24 / 2 = 31.2 kips. φVn = 1.0 × 0.6 × 50 × 15.9 × 0.275 = 131.2 kips. OK.
  5. Deflection: ΔL = 5 × (1.0/12) × 288⁴ / (384 × 29,000 × 375) = 0.69 in, against L/360 = 0.80 in. OK.

Use a W16x31. With ASD the answer is the same: Ma = 1.831 × 24² / 8 = 131.8 kip-ft against Mn/Ω = 50 × 54.0 / 12 / 1.67 = 134.7 kip-ft. If the floor needed a stiffer beam, a W18x35 (Ix = 510 in⁴) would cut the deflection to 0.51 in for 4 lb/ft more steel.

Before You Buy Steel

This is a preliminary size. A real beam also needs its bearing and connections checked, lateral bracing confirmed, and loads taken from the building code, so have a licensed engineer sign off. For the FE exam, this is the exact sequence the steel beam problems expect; review it in the FE steel design lesson.

Steel Beam Sizing FAQ

How do I calculate what size steel beam I need?

Find the maximum moment (wL²/8 for a simply supported beam under uniform load), divide by the design stress to get the required plastic section modulus Zx = Mu/(0.9Fy) for LRFD, pick the lightest W-shape with at least that Zx, then check shear and deflection with the beam weight included.

Should I use Sx or Zx to size a steel beam?

Current AISC 360 design uses the plastic modulus Zx for compact, laterally braced W-shapes, since Mn = FyZx. The elastic modulus Sx belongs to the older allowable stress method (fb = M/Sx ≤ 0.66Fy) and to first-yield checks. Both give similar answers for typical beams.

What deflection limit should a steel beam meet?

Common limits are L/360 under live load for floor members and L/240 for many roof members. Building codes such as IBC Table 1604.3 list the limits; check the one that applies to your project.

What if my beam is not braced along its length?

Then lateral-torsional buckling can govern and the beam may need a heavier shape. If the unbraced length Lb is longer than Lp (about 4 to 7 ft for many W16 to W24 shapes), use the AISC unbraced-length charts or have an engineer check it. This calculator assumes continuous bracing.

Related tools and topics