Length × width × depth to cubic yards, with ft³, m³ and tons of concrete, gravel, sand, topsoil, asphalt or mulch.
Weight uses 3,915 lb per yd³, a typical value. Moisture and gradation change it, so use your supplier's number when you have one.
Cubic yards = length (ft) × width (ft) × depth (ft) ÷ 27. Depth is usually measured in inches, so divide it by 12 first. One cubic yard is a 3 × 3 × 3 ft cube: 27 ft³, or 0.7646 m³.
For an L-shaped or irregular area, split it into rectangles and circles, or measure the area and use the known-area mode.
A cubic yard spread at depth D inches covers 27 × 12 ÷ D = 324 ÷ D square feet. This is the quickest check for mulch, gravel and topsoil orders.
| Depth | Area per yd³ | Typical use |
|---|---|---|
| 2 in | 162 ft² | Topdressing, decorative stone |
| 3 in | 108 ft² | Mulch beds, pathway gravel |
| 4 in | 81 ft² | Patio and sidewalk slabs, driveway gravel top layer |
| 6 in | 54 ft² | Driveway slabs, gravel base |
| 8 in | 40.5 ft² | Thick gravel driveway (two layers) |
| 12 in | 27 ft² | Raised beds, fill |
Gravel, sand and soil are often sold by the ton, so multiply the yards by the weight per yard. These are typical figures; the calculator lets you replace them with your supplier's number.
| Material | Typical lb/yd³ | Tons per yd³ (range) |
|---|---|---|
| Concrete | 3,915 | 1.96 (1.9–2.0) |
| Gravel | 2,835 | 1.42 (1.42–1.69) |
| Sand | 2,619 | 1.31 (1.31–1.61) |
| Topsoil (loam) | 2,160 | 1.08 (1.03–1.08) |
| Asphalt (compacted) | 3,960 | 1.98 (1.9–2.0) |
| Mulch (bark) | 405 | 0.20 (0.14–0.27) |
Concrete uses 145 lb/ft³, the normal-weight value behind the ACI 318 modulus formula Ec = 57,000√f′c (see concrete strength and modulus). Asphalt uses the paving rule of thumb of 110 lb per square yard per inch of compacted thickness (about 147 lb/ft³). Gravel, sand and topsoil (loam) use dry bulk densities from Engineering ToolBox, with the range running dry to wet; mulch uses its bark range of 10 to 20 lb/ft³ (wet mulch is heavier). All vary with moisture and grading, so treat those rows as estimates. Ready-mix concrete is ordered by volume, not weight; for bag counts use the concrete calculator.
12 × 12 × (4 ÷ 12) = 48 ft³ ÷ 27 = 1.78 yd³ (1.36 m³). With 10% extra it is 1.96 yd³, so order 2 yd³. The concrete slab calculator adds a thickness chart and bag counts.
50 × 10 × (4 ÷ 12) = 166.7 ft³ = 6.17 yd³. At 1.42 tons per yard (dry gravel) that is 8.8 tons. Gravel settles and packs down when rolled, so add about 10%: 6.8 yd³ or 9.6 tons.
π/4 × 10² × (3 ÷ 12) = 19.6 ft³ = 0.73 yd³, about 1.0 ton of gravel.
200 ft² of beds at 3 in: 200 × 0.25 = 50 ft³ = 1.85 yd³ of mulch. An 8 × 4 ft raised bed 12 in deep: 32 ft³ = 1.19 yd³ of soil, about 1.3 tons at 2,160 lb/yd³.
5 × 4 × 0.10 = 2.0 m³ = 2.62 yd³ (70.6 ft³).
Soil and rock change volume when dug and when compacted. A yard in the ground (bank) becomes more than a yard in the truck (loose) and less than a yard once rolled (compacted). For small jobs, 10 to 15% extra covers it. For fills, size the order by dry unit weight as shown in the soil compaction calculator. Large cut and fill volumes between survey cross sections use the average end area method from the NCEES FE Reference Handbook; see the FE earthwork volume example.
Multiply length × width in feet, then by the depth in feet (inches ÷ 12), and divide by 27. A 12 × 12 ft area 4 in deep is 12 × 12 × 0.333 = 48 ft³, or 1.78 yd³.
27. A cubic yard is 3 ft × 3 ft × 3 ft. It is also 0.7646 m³, so 1 m³ is 1.308 yd³.
324 ÷ depth in inches, in square feet: 162 ft² at 2 in, 108 ft² at 3 in, 81 ft² at 4 in and 54 ft² at 6 in.
About 1.4 tons dry (105 lb/ft³ × 27 = 2,835 lb) and about 1.7 tons wet (125 lb/ft³), using Engineering ToolBox bulk densities. Crushed stone and well-graded mixes vary, so ask the quarry which number they bill by.
Length × width × thickness ÷ 27, with the thickness in feet. A 20 × 20 ft slab 4 in thick is 133.3 ft³ = 4.94 yd³. Order 5 to 10% extra and round up to the supplier’s increment (often ¼ or ½ yd³).