Bending Stress Formula and Calculator

σ = Mc/I for the maximum bending stress and τ = VQ/Ib for shear. Pick a section, enter M and V, and get both stresses.

8.72ksi
Max bending stress σ = Mc/I (tension one face, compression the other)
Max shear, VQ/Ib
2.141 ksi
I
825.3 in⁴
S = I/c
103.16 in³
c
8.000 in
Q at neutral axis
58.89 in³
Area
19.25 in²

Linear-elastic, prismatic beam bending about its strong (x) axis. Shear is at the neutral axis, where it is largest for these shapes; for Custom, it is at the point you give Q and t for.

The Bending Stress Formula

The flexure formula gives the normal stress in a beam at a distance from the neutral axis:

  • M: bending moment at the section (often largest where the shear diagram crosses zero)
  • y: distance from the neutral axis; c is its largest value, to the extreme fiber
  • I: moment of inertia of the cross-section about the neutral axis
  • S: elastic section modulus, the number steel tables list as Sx

Stress varies linearly through the depth: zero at the neutral axis, maximum compression on one face and maximum tension on the other. The formula assumes a straight, prismatic, linear-elastic beam bent about a principal axis. It is in the Mechanics of Materials chapter of the NCEES FE Reference Handbook, under Beams, written as so that fibers above the axis are in compression under a positive moment.

The Shear Stress Formula: τ = VQ/Ib

The same Handbook section gives the transverse shear stress at any height in the section:

  • V: shear force at the section, from the shear diagram
  • Q: first moment, about the neutral axis, of the area between the point and the nearest free edge; is the distance from the neutral axis to that area's centroid
  • b: width of the section at the point (the web thickness tw in an I-beam)

Q is largest at the neutral axis, so that is where shear stress peaks for common shapes. The shortcuts follow directly:

SectionIMax bending stressMax shear stress
Rectangle b × hbh³/126M/(bh²)1.5 V/A
Solid circle, diameter dπd⁴/6432M/(πd³)4V/(3A)
I-beamfrom tables or partsM/SxVQ/(I tw), roughly V/(d tw)

Need I or Q for an odd shape? Get them from the moment of inertia calculator, then enter them as Custom I in the calculator above.

Worked Example 1: Steel I-Beam, Simply Supported

A 20 ft simply supported beam carries 1.5 kip/ft. The section is a built-up I-beam: flanges 8 × 0.75 in, web 0.5 in thick, total depth 16 in. Find the maximum bending and shear stress.

  1. Moment: M = wL²/8 = 1.5 × 20² / 8 = 75 kip·ft = 900 kip·in
  2. Shear: V = wL/2 = 1.5 × 20 / 2 = 15 kips
  3. Moment of inertia: I = [8 × 16³ − (8 − 0.5) × 14.5³] / 12 = 825.3 in⁴, and c = 8 in
  4. Bending stress: σ = Mc/I = 900 × 8 / 825.3 = 8.72 ksi (S = 103.2 in³)
  5. Q at the neutral axis: flange 8 × 0.75 × 7.625 = 45.75 in³, plus half the web 0.5 × 7.25 × 3.625 = 13.14 in³, total 58.89 in³
  6. Shear stress: τ = VQ/(I tw) = 15 × 58.89 / (825.3 × 0.5) = 2.14 ksi

At the top of the web, where it meets the flange, Q drops to 45.75 in³ and τ = 15 × 45.75 / (825.3 × 0.5) = 1.66 ksi. The quick estimate V/(d tw) = 15 / (16 × 0.5) = 1.88 ksi sits between the two; steel design checks web shear on a similar d·tw area. These are the calculator's default inputs. To get M and V for other loads and supports, draw the diagrams in the beam calculator.

Worked Example 2: Timber Beam in SI Units

A 100 × 300 mm rectangular beam carries M = 20 kN·m and V = 30 kN.

  1. Convert: M = 20 × 10⁶ N·mm, V = 30 × 10³ N
  2. Section modulus: S = bh²/6 = 100 × 300² / 6 = 1.5 × 10⁶ mm³
  3. Bending stress: σ = M/S = 20 × 10⁶ / 1.5 × 10⁶ = 13.3 MPa
  4. Shear stress: τ = 1.5 V/A = 1.5 × 30,000 / 30,000 = 1.5 MPa

Switch the calculator to kN, mm and pick Rectangle to check it. Shear governs short, heavily loaded timber beams more often than steel ones, because wood is weak in horizontal shear along the grain.

Common Mistakes

  • Mixing kip·ft and inches. Multiply M by 12 before dividing by I in in⁴, or the answer is 12 times too small.
  • Using the full flange width for b in τ = VQ/Ib at a point in the web. Use the width where the cut is.
  • Taking Q about the base instead of the neutral axis, or using the whole area instead of the part beyond the cut.
  • Using c to the near face of an unsymmetric section (a T-beam). Tension and compression faces have different c; check both.
  • Checking σ and τ separately where both are large, such as the top of the web. There the largest normal stress is the principal stress: enter σ and τ in the principal stress (Mohr's circle) calculator.

Both formulas are common on the FE exam. Practice them with the FE bending stress example and FE shear stress example, and to pick a W-shape for a required Sx, use the steel beam size calculator.

Bending and Shear Stress FAQ

What is the bending stress formula?

σ = My/I, where M is the bending moment at the section, y the distance from the neutral axis and I the moment of inertia about that axis. The maximum is at the extreme fiber, y = c, so σmax = Mc/I = M/S, where S = I/c is the elastic section modulus.

What is the shear stress formula for a beam?

τ = VQ/(Ib), where V is the shear force, Q the first moment of the area above (or below) the point about the neutral axis, I the moment of inertia of the whole section and b the width of the section at that point. It is largest at the neutral axis for rectangles, circles and I-beams.

Why is maximum shear stress 1.5 V/A for a rectangle?

At the neutral axis Q = (b·h/2)(h/4) = bh²/8 and I = bh³/12, so τ = V(bh²/8)/((bh³/12)b) = 3V/(2bh) = 1.5 V/A. For a solid circle the same steps give 4V/(3A).

Is bending stress tension or compression?

Both. Under a positive (sagging) moment the top fibers are in compression and the bottom fibers in tension, with zero stress at the neutral axis. The FE Reference Handbook writes σx = −My/I so that a positive y (above the axis) gives compression.

What units come out of σ = Mc/I?

Force per area. With M in kip·in, c in in and I in in⁴ you get ksi. Watch kip·ft: multiply by 12 first. In SI, M in N·mm, c in mm and I in mm⁴ gives N/mm², which is MPa.

Related tools and topics