Studying for the FE Civil exam? 427 practice problems with worked solutions, sorted by exam topic.
Practice FE problemsHow to Use the Shear and Moment Diagram Calculator
- 1
Add supports
Pin, roller or fixed, anywhere on the span.
- 2
Apply loads
Point loads, distributed loads and applied moments.
- 3
Read the results
Reactions, shear force diagram and bending moment diagram, solved with the direct stiffness method.
How the Beam Calculator Works
The direct stiffness method solves support reactions, then shear and moment. It handles simple spans, overhangs, cantilevers, propped, fixed-fixed and continuous beams.
For deflection from E and I, use the beam deflection calculator and span/δ check to compare your service-load result with the applicable deflection limit. Get I about the bending axis with the moment of inertia calculator and grid-unit example. Scale its grid results to in⁴ or mm⁴ before using them in beam formulas. For stresses (σ = Mc/I, τ = VQ/Ib), use the bending stress calculator, get S from the section modulus calculator, or choose a W-shape with the steel beam size calculator. When normal and shear stress act at the same point, combine them with the Mohr's circle calculator and result checks to find principal stresses. For connection bolts with known axial tension, use the bolt tensile stress area formula to distinguish threaded-section area from nominal shank area.
For a pin-jointed structure carrying loads at its joints, use the truss calculator and checked Warren-truss example to find axial tension and compression in each member.
Shear Force and Bending Moment Formulas
Load, shear and moment are linked by two derivatives (NCEES FE Reference Handbook, Mechanics of Materials, Beams). With w as a downward load per unit length:
| Relationship | Formula | What it means on the diagrams |
|---|
| Load to shear | dV/dx = −w | The SFD slopes down at the rate of the distributed load |
| Shear to moment | dM/dx = V | Check shear zero crossings, boundaries and jumps for extreme moments |
| Change in shear | V₂ − V₁ = −∫w dx | Equals minus the load between two sections |
| Change in moment | M₂ − M₁ = ∫V dx | Equals the area under the SFD |
Point loads create shear jumps and moment kinks; applied moments create moment jumps only. For wL²/8, PL/4 and other maxima, see the maximum bending moment formulas and the beam deflection formulas table.
How to Draw Shear and Moment Diagrams by Hand
See the shear and moment diagrams guide:
- Find reactions: ΣFy = 0; ΣM = 0 about one support.
- Draw shear: upward forces jump up, downward forces jump down; uniform downward loads give slope −w.
- Draw moment from signed shear areas. Start at zero for a free or pin/roller end without an end couple; otherwise use the boundary moment.
- Compare moment magnitudes at shear zero crossings, point loads, supports and beam ends, including both sides of applied couples. Check the far-end moment against its boundary condition.
Use these shape rules to check each segment:
| Load on the segment | Shear diagram | Moment diagram |
|---|
| No load | Horizontal line | Straight sloped line |
| Uniform load w | Straight line, slope −w | Parabola (2nd degree) |
| Linearly varying load | Parabola | Cubic curve |
| Point load P | Sudden jump of P | Kink (change in slope) |
| Applied moment M₀ | No change | Sudden jump of M₀ |
Worked Example: Point Load Plus Uniform Load
A 20 ft simply supported beam (pin at A, roller at B) carries a uniform load of 2 kip/ft over the full span and a 10 kip point load 5 ft from A.
- Reactions. ΣMA = 0: RB = (2 × 20 × 10 + 10 × 5) / 20 = 22.5 kip. ΣFy = 0: RA = 40 + 10 − 22.5 = 27.5 kip.
- Shear. V starts at +27.5 kip and drops 2 kip/ft to 17.5 kip just left of the point load, jumps down to 7.5 kip, then reaches zero at x = 5 + 7.5 / 2 = 8.75 ft and ends at −22.5 kip (= −RB).
- Moment. Under the point load, M = 27.5 × 5 − 2 × 5² / 2 = 112.5 kip·ft. At zero shear, Mmax = 27.5 × 8.75 − 10 × 3.75 − 2 × 8.75² / 2 = 126.6 kip·ft (sagging). M returns to zero at B.
How to Read the Shear and Moment Diagrams
Measure x from A. At point loads, read shear before and after the jump:
| Position x (ft) | Shear V (kip) | Moment M (kip·ft) |
|---|
| 0, just right of A | +27.5 | 0 |
| 5, just before / after load | +17.5 / +7.5 | 112.5 on both sides |
| 8.75, zero shear | 0 | 126.6 (maximum) |
| 10, midspan | −2.5 | 125.0 |
| 20, just left of B | −22.5 | 0 |
The maximum, 126.6 kip·ft at 8.75 ft, is not under the point load (112.5) or at midspan (125.0): it sits where shear crosses zero.
Check signed shear areas: (27.5 + 17.5) × 5 / 2 = 112.5 kip·ft from 0–5 ft; 7.5 × 3.75 / 2 = 14.0625 kip·ft from 5–8.75 ft. Their sum is 126.5625 kip·ft. From 8.75–20 ft, −22.5 × 11.25 / 2 = −126.5625 kip·ft returns moment to zero. At B the reaction closes shear to zero. Force balance: 27.5 + 22.5 = 40 + 10 = 50 kip.
Practice these checks with FE mechanics of materials, an FE Civil practice exam or these free FE practice problems.
More Worked Beam Examples
Hand calculations you can open in the calculator to check.
Example 1Simply supported beam with a uniform load
A 6 m beam, pinned at the left end and on a roller at the right, carries 10 kN/m over its full length.
- R_A = R_B
- 30 kN
- M_max
- 45 kN·m
›Solution
- Reactions: Total load = 10 × 6 = 60 kN, shared equally: R_A = R_B = 30 kN.
- Shear: Shear starts at +30 kN, falls in a straight line, crosses zero at midspan (3 m) and ends at −30 kN.
- Moment: Maximum moment is at the zero-shear point: M_max = wL²/8 = 10 × 6² / 8 = 45 kN·m at midspan. The diagram is a parabola.
Open in calculator →Example 2Simply supported beam with a center point load
An 8 m simply supported beam carries a single 20 kN load at midspan.
- R_A = R_B
- 10 kN
- M_max
- 40 kN·m
›Solution
- Reactions: By symmetry, R_A = R_B = 20 / 2 = 10 kN.
- Shear: Shear is +10 kN from the left support to the load, then jumps down by 20 kN to −10 kN.
- Moment: Moment rises linearly to M_max = PL/4 = 20 × 8 / 4 = 40 kN·m under the load, where shear changes sign. The diagram is a triangle.
Open in calculator →Example 3Cantilever with a uniform load
A 3 m cantilever, fixed at the left end and free at the right, carries 5 kN/m over its full length.
- R
- 15 kN
- M_fixed
- 22.5 kN·m
›Solution
- Reactions: Vertical reaction R = 5 × 3 = 15 kN; fixed-end moment M = wL²/2 = 5 × 3² / 2 = 22.5 kN·m.
- Shear: Shear is 15 kN at the fixed end and falls linearly to zero at the free end.
- Moment: Moment magnitude is largest at the support, 22.5 kN·m (hogging), and drops to zero at the free tip along a parabola.
Open in calculator → Sign Convention
- Reactions
- Upward is positive
- Shear
- Positive when the left side is pushed up
- Moment
- Sagging (tension on the bottom) is positive
For downward loads without couples: simple spans sag, cantilevers hog. See the FE Reference Handbook.
Shear and Moment Diagram Calculator FAQ
What is a shear and moment diagram?
+
The shear force diagram (SFD) plots internal shear V along a beam; the bending moment diagram (BMD) plots internal moment M.
How do I draw a shear and moment diagram with this calculator?
+
Add supports and point, distributed or moment loads. The calculator plots both diagrams automatically.
Is this beam calculator free?
+
Yes. It is a free online beam calculator: support reactions, the shear force diagram (SFD) and bending moment diagram (BMD) need no sign-up.
What supports and loads are supported?
+
Pin, roller and fixed supports, with point loads, distributed loads and applied moments.
Where is the maximum bending moment on a beam?
+
Check shear zero crossings, point loads, supports, beam ends and both sides of applied couples. Compare absolute moment values.
How do I find beam support reactions?
+
For a simply supported beam, use ΣFy = 0 and ΣM = 0. The 20 ft worked example on this page (2 kip/ft plus a 10 kip point load) gives reactions of 27.5 and 22.5 kip, balancing 50 kip downward. The calculator reports support reactions.
Can it solve statically indeterminate beams?
+
Yes. The solver uses the direct stiffness method, so continuous beams, propped cantilevers and fixed-fixed beams work the same way as simple spans.
How do I get bending stress from the moment diagram?
+
Take the largest moment magnitude from the bending moment diagram and use the flexure formula σ = Mc/I, or σ = M/S with the elastic section modulus S = I/c. Keep units consistent, for example kip·in with in³ to get ksi.
Which units can I use?
+
Choose SI (m, N, N·m) or US customary (ft, kip, kip·ft or kip·in).
Related